CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

KS0108 Driver For MikroElektronika EasyPic 4 Board

 
Post new topic   Reply to topic    CCS Forum Index -> Code Library
View previous topic :: View next topic  
Author Message
hansolo



Joined: 06 Oct 2006
Posts: 20

View user's profile Send private message

KS0108 Driver For MikroElektronika EasyPic 4 Board
PostPosted: Mon Oct 30, 2006 5:26 pm     Reply with quote

This driver is for the 128x64 GLCD from Xiamen Ocular which is supplied as optional item when purchasing the Mikroelektronika EasyPic 4 Board.

This driver is modified from the Hantronix driver supplied by CCS to adapt to this GLCD and board. Modification done on the original driver is :
1) Swapped CS1 and CS2 pins
2) I/O pins adjusted to suit the board and GLCD

Hope this is useful:

Code:
/////////////////////////////////////////////////////////////////////////
////                           ks0108_mE_EP4.c                       ////
////                                                                 ////
//// This file contains drivers for using a LGM12864B-FL-YBW with    ////
//// a KS0108 display controller. This GLCD is 128 by 64 pixels.     ////
//// The driver treats the upper left pixel as (0,0).                ////
////                                                                 ////
//// Use #define FAST_GLCD if the target chip has at least 1k of RAM ////
//// to decrease the time it takes to update the display.            ////
//// glcd_update() must then be called to update the display after   ////
//// changing the pixel information.                                 ////
//// See ex_glcd.c for suggested usage.                              ////
//// See KS0108.c for controlling a single 64 by 64 display          ////
/////////////////////////////////////////////////////////////////////////
////                                                                 ////
//// LCD Pin connections:                                            ////
//// (These can be changed as needed in the following defines).      ////
////  * 1: Chip Select 1 is connected to B1                          ////
////  * 2: Chip Select 2 is connected to B0                          ////
////  * 3: VSS is connected to GND                                   ////
////  * 4: VDD is connected to +5V                                   ////
////  * 5: V0  - LCD operating voltage (Constrast adjustment)        ////
////  * 6: R/S - Register select is connected to B2                  ////
////  * 7: R/W - Read or Write is connected to B3                    ////
////  * 8: Enable is connected to B4                                 ////
////  *9-16: Data Bus 0 to 7 is connected to port D                  ////
////  *17: Reset is connected to B5                                  ////
////  *18: Negative voltage is also connected to the 20k Ohm POT     ////
////  *19: Positive voltage for LED backlight is connected to +5V    ////
////  *20: Negavtive voltage for LED backlight is connected to GND   ////
////                                                                 ////
/////////////////////////////////////////////////////////////////////////
////                                                                 ////
////  glcd_init(mode)                                                ////
////     * Must be called before any other function.                 ////
////       - mode can be ON or OFF to turn the LCD on or off         ////
////                                                                 ////
////  glcd_pixel(x,y,color)                                          ////
////     * Sets the pixel to the given color.                        ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_fillScreen(color)                                         ////
////     * Fills the entire LCD with the given color.                ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_update()                                                  ////
////     * Write the display data stored in RAM to the LCD           ////
////     * Only available if FAST_GLCD is defined                    ////
////                                                                 ////
/////////////////////////////////////////////////////////////////////////
////        (C) Copyright 1996, 2004 Custom Computer Services        ////
//// This source code may only be used by licensed users of the CCS  ////
//// C compiler.  This source code may only be distributed to other  ////
//// licensed users of the CCS C compiler.  No other use,            ////
//// reproduction or distribution is permitted without written       ////
//// permission.  Derivative programs created using this software    ////
//// in object code form are not restricted in any way.              ////
/////////////////////////////////////////////////////////////////////////



#ifndef HDM64GS12
#define HDM64GS12

#ifndef GLCD_WIDTH
#define GLCD_WIDTH   128
#endif

#ifndef GLCD_CS1
#define GLCD_CS1     PIN_B1   // Chip Selection 1
#endif

#ifndef GLCD_CS2
#define GLCD_CS2     PIN_B0   // Chip Selection 2
#endif

#ifndef GLCD_DI
#define GLCD_DI      PIN_B2   // Data or Instruction input
#endif

#ifndef GLCD_RW
#define GLCD_RW      PIN_B3   // Read/Write
#endif

#ifndef GLCD_E
#define GLCD_E       PIN_B4   // Enable
#endif

#ifndef GLCD_RST
#define GLCD_RST     PIN_B5   // Reset
#endif

#define GLCD_LEFT    0
#define GLCD_RIGHT   1

#ifndef ON
#define ON           1
#endif

#ifndef OFF
#define OFF          0
#endif

/////////////////////////////////////////////////////////////////////////
// Function Prototypes
/////////////////////////////////////////////////////////////////////////
void glcd_init(int1 mode);
void glcd_pixel(int8 x, int8 y, int1 color);
void glcd_fillScreen(int1 color);
void glcd_writeByte(int1 side, BYTE data);
BYTE glcd_readByte(int1 side);
void glcd_update();
/////////////////////////////////////////////////////////////////////////

#ifdef FAST_GLCD
struct
{
   int8 left[512];
   int8 right[512];
} displayData;
#endif


// Purpose:       Initialize the LCD.
//                Call before using any other LCD function.
// Inputs:        OFF - Turns the LCD off
//                ON  - Turns the LCD on
void glcd_init(int1 mode)
{
   // Initialze some pins
   output_high(GLCD_RST);
   output_low(GLCD_E);
   output_low(GLCD_CS1);
   output_low(GLCD_CS2);

   output_low(GLCD_DI);                 // Set for instruction
   glcd_writeByte(GLCD_LEFT,  0xC0);    // Specify first RAM line at the top
   glcd_writeByte(GLCD_RIGHT, 0xC0);    //   of the screen
   glcd_writeByte(GLCD_LEFT,  0x40);    // Set the column address to 0
   glcd_writeByte(GLCD_RIGHT, 0x40);
   glcd_writeByte(GLCD_LEFT,  0xB8);    // Set the page address to 0
   glcd_writeByte(GLCD_RIGHT, 0xB8);

   if(mode == ON)
   {
      glcd_writeByte(GLCD_LEFT,  0x3F); // Turn the display on
      glcd_writeByte(GLCD_RIGHT, 0x3F);
   }
   else
   {
      glcd_writeByte(GLCD_LEFT,  0x3E); // Turn the display off
      glcd_writeByte(GLCD_RIGHT, 0x3E);
   }

   glcd_fillScreen(OFF);                // Clear the display

   #ifdef FAST_GLCD
   glcd_update();
   #endif
}


// Purpose:    Update the LCD with data from the display arrays
#ifdef FAST_GLCD
void glcd_update()
{
   int8 i, j;
   int8 *p1, *p2;

   p1 = displayData.left;
   p2 = displayData.right;

   // Loop through the vertical pages
   for(i = 0; i < 8; ++i)
   {
      output_low(GLCD_DI);                      // Set for instruction
      glcd_writeByte(GLCD_LEFT, 0x40);          // Set horizontal address to 0
      glcd_writeByte(GLCD_RIGHT, 0x40);
      glcd_writeByte(GLCD_LEFT, i | 0xB8);      // Set page address
      glcd_writeByte(GLCD_RIGHT, i | 0xB8);
      output_high(GLCD_DI);                     // Set for data

      // Loop through the horizontal sections
      for(j = 0; j < 64; ++j)
      {
         glcd_writeByte(GLCD_LEFT, *p1++);      // Turn pixels on or off
         glcd_writeByte(GLCD_RIGHT, *p2++);     // Turn pixels on or off
      }
   }
}
#endif


// Purpose:    Turn a pixel on a graphic LCD on or off
// Inputs:     1) x - the x coordinate of the pixel
//             2) y - the y coordinate of the pixel
//             3) color - ON or OFF
void glcd_pixel(int8 x, int8 y, int1 color)
#ifdef FAST_GLCD
{
   int8* p;
   int16 temp;
   temp =  y/8;
   temp *= 64;
   temp += x;

   if(x > 63)
   {
      p = displayData.right + temp - 64;
   }
   else
   {
      p = displayData.left + temp;
   }

   if(color)
   {
      bit_set(*p, y%8);
   }
   else
   {
      bit_clear(*p, y%8);
   }
}
#else
{
   BYTE data;
   int1 side = GLCD_LEFT;  // Stores which chip to use on the LCD

   if(x > 63)              // Check for first or second display area
   {
      x -= 64;
      side = GLCD_RIGHT;
   }

   output_low(GLCD_DI);                         // Set for instruction
   bit_clear(x,7);                              // Clear the MSB. Part of an instruction code
   bit_set(x,6);                                // Set bit 6. Also part of an instruction code
   glcd_writeByte(side, x);                     // Set the horizontal address
   glcd_writeByte(side, (y/8 & 0xBF) | 0xB8);   // Set the vertical page address
   output_high(GLCD_DI);                        // Set for data
   glcd_readByte(side);                         // Need two reads to get data
   data = glcd_readByte(side);                  //  at new address

   if(color == ON)
      bit_set(data, y%8);        // Turn the pixel on
   else                          // or
      bit_clear(data, y%8);      // turn the pixel off

   output_low(GLCD_DI);          // Set for instruction
   glcd_writeByte(side, x);      // Set the horizontal address
   output_high(GLCD_DI);         // Set for data
   glcd_writeByte(side, data);   // Write the pixel data
}
#endif


// Purpose:    Fill the LCD screen with the passed in color
// Inputs:     ON  - turn all the pixels on
//             OFF - turn all the pixels off
void glcd_fillScreen(int1 color)
#ifdef FAST_GLCD
{
   int8  data;
   int8  *p1, *p2;
   int16 i;

   p1 = displayData.left;
   p2 = displayData.right;
   data = 0xFF * color;

   for(i=0; i<512; ++i)
   {
      *p1++ = data;
      *p2++ = data;
   }
}
#else
{
   int8 i, j;

   // Loop through the vertical pages
   for(i = 0; i < 8; ++i)
   {
      output_low(GLCD_DI);                      // Set for instruction
      glcd_writeByte(GLCD_LEFT, 0b01000000);    // Set horizontal address to 0
      glcd_writeByte(GLCD_RIGHT, 0b01000000);
      glcd_writeByte(GLCD_LEFT, i | 0b10111000);// Set page address
      glcd_writeByte(GLCD_RIGHT, i | 0b10111000);
      output_high(GLCD_DI);                     // Set for data

      // Loop through the horizontal sections
      for(j = 0; j < 64; ++j)
      {
         glcd_writeByte(GLCD_LEFT, 0xFF*color);  // Turn pixels on or off
         glcd_writeByte(GLCD_RIGHT, 0xFF*color); // Turn pixels on or off
      }
   }
}
#endif


// Purpose:    Write a byte of data to the specified chip
// Inputs:     1) chipSelect - which chip to write the data to
//             2) data - the byte of data to write
void glcd_writeByte(int1 side, BYTE data)
{
   if(side)                   // Choose which side to write to
      output_high(GLCD_CS2);
   else
      output_high(GLCD_CS1);

   output_low(GLCD_RW);       // Set for writing
   output_d(data);            // Put the data on the port
   delay_cycles(1);
   output_high(GLCD_E);       // Pulse the enable pin
   delay_cycles(5);
   output_low(GLCD_E);

   output_low(GLCD_CS1);      // Reset the chip select lines
   output_low(GLCD_CS2);
}


// Purpose:    Reads a byte of data from the specified chip
// Ouputs:     A byte of data read from the chip
BYTE glcd_readByte(int1 side)
{
   BYTE data;                 // Stores the data read from the LCD

   set_tris_d(0xFF);          // Set port d to input
   output_high(GLCD_RW);      // Set for reading

   if(side)                   // Choose which side to write to
      output_high(GLCD_CS2);
   else
      output_high(GLCD_CS1);

   delay_cycles(1);
   output_high(GLCD_E);       // Pulse the enable pin
   delay_cycles(4);
   data = input_d();          // Get the data from the display's output register
   output_low(GLCD_E);

   output_low(GLCD_CS1);      // Reset the chip select lines
   output_low(GLCD_CS2);
   return data;               // Return the read data
}

#endif
NigelGardner



Joined: 21 Nov 2006
Posts: 1
Location: Wiltshire, UK

View user's profile Send private message Visit poster's website

Code Problem
PostPosted: Tue Nov 21, 2006 11:20 am     Reply with quote

Thanks for this piece of code - saved me a lot.

I have the code working fine with an 18F482 in normal mode at 20MHz, but display gives garbage in fast update mode. Any thoughts?

Happy PICing, Nigel
cxnvcarol



Joined: 06 Nov 2011
Posts: 2

View user's profile Send private message MSN Messenger

example code
PostPosted: Sun Nov 06, 2011 9:46 pm     Reply with quote

Hello, in the comments of the code is mentioned a file for suggested usage (ex_glcd.c), do you have that file? can you post it? Thank you very much for your help.


+++++++++++++++++++++++
Its a violation of forum rules to ask for this file:

10. Don't post the CCS example code or drivers, or ask for such code and drivers.

Forum Rules
http://www.ccsinfo.com/forum/viewtopic.php?t=26245

-- Forum Moderator
+++++++++++++++++++++++

_________________
cxnv
cxnvcarol



Joined: 06 Nov 2011
Posts: 2

View user's profile Send private message MSN Messenger

PostPosted: Mon Nov 07, 2011 12:14 am     Reply with quote

Ok, with a little piece of code to illustrate how to use the functions should be enough. Thank you.
_________________
cxnv
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> Code Library All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group