CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

LC7981.C Modified LCD Version from CCS code

 
Post new topic   Reply to topic    CCS Forum Index -> Code Library
View previous topic :: View next topic  
Author Message
bwhiten



Joined: 26 Nov 2003
Posts: 151
Location: Grayson, GA

View user's profile Send private message

LC7981.C Modified LCD Version from CCS code
PostPosted: Thu May 29, 2008 9:52 am     Reply with quote

This also has some extra functions for using the built-in character map that I found useful. I have a #ORG in there to put the ascii map into ROM to save RAM.

Code:
/////////////////////////////////////////////////////////////////////////
////                         LC7981.C                                ////
////                                                                 ////
//// This file contains drivers for using a Crystalfontz CFAG16080A with ///
//// an LED backlight. The CFAG16080A is 160 pixles across and 80     ////
//// pixels down. The driver treats the upper left pixel as (0,0).   ////
////                                                                 ////
//// LCD Pin connections:                                            ////
//// (These can be changed as needed in the following defines).      ////
////  * 1: VSS is connected to GND                                   ////
////  * 2: VDD is connected to +5V                                   ////
////  * 3: V0 - LCD operating voltage is connected ..................////
////  * 4: R/S - Data or Instruction is connected to C5              ////
////  * 5: R/W - Read or Write is connected to C6                    ////
////  * 6: Enable is connected to C7                                 ////
////  *7-14: Data Bus 0 to 7 is connected to port d                  ////
////  *15: Chip Select is connected to E0                            ////
////  *16: Display Off is connected to E1                            ////
////  *17: Reset is connected to E2                                  ////
////  *18: Negative voltage is also connected .......................////
////  *19: Positive voltage for LED backlight is connected to +5V    ////
////  *20: Negavtive voltage for LED backlight is connected .........////
////                                                                 ////
////  glcd_init(mode)                                                ////
////     * Must be called before any other function.                 ////
////       - mode can be ON or OFF to turn the LCD on or off         ////
////                                                                 ////
////  glcd_pixel(x,y,color)                                          ////
////     * Sets the pixel to the given color.                        ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_line(x1,y1,x2,y2,color)                                   ////
////     * Draws a line from the first point to the second point     ////
////       with the given color.                                     ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_rect(x1,y1,x2,y2,fill,color)                              ////
////     * Draws a rectangle with upper left point (x1,y1) and lower ////
////       right point (x2,y2).                                      ////
////       - fill can be YES or NO                                   ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_bar(x1,y1,x2,y2,width,color)                              ////
////     * Draws a bar (wide line) from the first point to the       ////
////       second point.                                             ////
////       - width is the number of pixels wide                      ////
////       - color is ON or OFF                                      ////
////                                                                 ////
////  glcd_circle(x,y,radius,fill,color)                             ////
////     * Draws a circle with center at (x,y)                       ////
////       - fill can be YES or NO                                   ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
////  glcd_text57(x,y,textptr,size,color)                            ////
////     * Write the null terminated text pointed to by textptr with ////
////       the upper left coordinate of the first character at (x,y).////
////       Characters are 5 pixels wide and 7 pixels tall.           ////
////       - size is an integer that scales the size of the text     ////
////       - color is ON or OFF                                      ////
////     * Note - The given text is character wrapped. If this       ////
////       function is used on a different size display, then change ////
////       the GLCD_WIDTH define appropriately.                      ////
////                                                                 ////
////  glcd_fillScreen(color)                                         ////
////     * Fills the entire LCD with the given color.                ////
////       - color can be ON or OFF                                  ////
////                                                                 ////
/////////////////////////////////////////////////////////////////////////
////        (C) Copyright 1996,2003 Custom Computer Services         ////
//// This source code may only be used by licensed users of the CCS  ////
//// C compiler.  This source code may only be distributed to other  ////
//// licensed users of the CCS C compiler.  No other use,            ////
//// reproduction or distribution is permitted without written       ////
//// permission.  Derivative programs created using this software    ////
//// in object code form are not restricted in any way.              ////
/////////////////////////////////////////////////////////////////////////
#ORG 0x1000
const int8 TEXT[51][5] ={0x00, 0x00, 0x00, 0x00, 0x00, // SPACE
                         0x00, 0x00, 0x5F, 0x00, 0x00, // !
                         0x00, 0x03, 0x00, 0x03, 0x00, // "
                         0x14, 0x3E, 0x14, 0x3E, 0x14, // #
                         0x24, 0x2A, 0x7F, 0x2A, 0x12, // $
                         0x43, 0x33, 0x08, 0x66, 0x61, // %
                         0x36, 0x49, 0x55, 0x22, 0x50, // &
                         0x00, 0x05, 0x03, 0x00, 0x00, // '
                         0x00, 0x1C, 0x22, 0x41, 0x00, // (
                         0x00, 0x41, 0x22, 0x1C, 0x00, // )
                         0x14, 0x08, 0x3E, 0x08, 0x14, // *
                         0x08, 0x08, 0x3E, 0x08, 0x08, // +
                         0x00, 0x50, 0x30, 0x00, 0x00, // ,
                         0x08, 0x08, 0x08, 0x08, 0x08, // -
                         0x00, 0x60, 0x60, 0x00, 0x00, // .
                         0x20, 0x10, 0x08, 0x04, 0x02, // /
                         0x3E, 0x51, 0x49, 0x45, 0x3E, // 0
                         0x04, 0x02, 0x7F, 0x00, 0x00, // 1
                         0x42, 0x61, 0x51, 0x49, 0x46, // 2
                         0x22, 0x41, 0x49, 0x49, 0x36, // 3
                         0x18, 0x14, 0x12, 0x7F, 0x10, // 4
                         0x27, 0x45, 0x45, 0x45, 0x39, // 5
                         0x3E, 0x49, 0x49, 0x49, 0x32, // 6
                         0x01, 0x01, 0x71, 0x09, 0x07, // 7
                         0x36, 0x49, 0x49, 0x49, 0x36, // 8
                         0x26, 0x49, 0x49, 0x49, 0x3E, // 9
                         0x00, 0x36, 0x36, 0x00, 0x00, // :
                         0x00, 0x56, 0x36, 0x00, 0x00, // ;
                         0x08, 0x14, 0x22, 0x41, 0x00, // <
                         0x14, 0x14, 0x14, 0x14, 0x14, // =
                         0x00, 0x41, 0x22, 0x14, 0x08, // >
                         0x02, 0x01, 0x51, 0x09, 0x06, // ?
                         0x3E, 0x41, 0x59, 0x55, 0x5E, // @
                         0x7E, 0x09, 0x09, 0x09, 0x7E, // A
                         0x7F, 0x49, 0x49, 0x49, 0x36, // B
                         0x3E, 0x41, 0x41, 0x41, 0x22, // C
                         0x7F, 0x41, 0x41, 0x41, 0x3E, // D
                         0x7F, 0x49, 0x49, 0x49, 0x41, // E
                         0x7F, 0x09, 0x09, 0x09, 0x01, // F
                         0x3E, 0x41, 0x41, 0x49, 0x3A, // G
                         0x7F, 0x08, 0x08, 0x08, 0x7F, // H
                         0x00, 0x41, 0x7F, 0x41, 0x00, // I
                         0x30, 0x40, 0x40, 0x40, 0x3F, // J
                         0x7F, 0x08, 0x14, 0x22, 0x41, // K
                         0x7F, 0x40, 0x40, 0x40, 0x40, // L
                         0x7F, 0x02, 0x0C, 0x02, 0x7F, // M
                         0x7F, 0x02, 0x04, 0x08, 0x7F, // N
                         0x3E, 0x41, 0x41, 0x41, 0x3E, // O
                         0x7F, 0x09, 0x09, 0x09, 0x06, // P
                         0x1E, 0x21, 0x21, 0x21, 0x5E, // Q
                         0x7F, 0x09, 0x09, 0x09, 0x76};// R

#ORG 0x1000
const int8 TEXT2[44][5]={0x26, 0x49, 0x49, 0x49, 0x32, // S
                         0x01, 0x01, 0x7F, 0x01, 0x01, // T
                         0x3F, 0x40, 0x40, 0x40, 0x3F, // U
                         0x1F, 0x20, 0x40, 0x20, 0x1F, // V
                         0x7F, 0x20, 0x10, 0x20, 0x7F, // W
                         0x41, 0x22, 0x1C, 0x22, 0x41, // X
                         0x07, 0x08, 0x70, 0x08, 0x07, // Y
                         0x61, 0x51, 0x49, 0x45, 0x43, // Z
                         0x00, 0x7F, 0x41, 0x00, 0x00, // [
                         0x02, 0x04, 0x08, 0x10, 0x20, // \
                         0x00, 0x00, 0x41, 0x7F, 0x00, // ]
                         0x04, 0x02, 0x01, 0x02, 0x04, // ^
                         0x40, 0x40, 0x40, 0x40, 0x40, // _
                         0x00, 0x01, 0x02, 0x04, 0x00, // `
                         0x20, 0x54, 0x54, 0x54, 0x78, // a
                         0x7F, 0x44, 0x44, 0x44, 0x38, // b
                         0x38, 0x44, 0x44, 0x44, 0x44, // c
                         0x38, 0x44, 0x44, 0x44, 0x7F, // d
                         0x38, 0x54, 0x54, 0x54, 0x18, // e
                         0x04, 0x04, 0x7E, 0x05, 0x05, // f
                         0x08, 0x54, 0x54, 0x54, 0x3C, // g
                         0x7F, 0x08, 0x04, 0x04, 0x78, // h
                         0x00, 0x44, 0x7D, 0x40, 0x00, // i
                         0x20, 0x40, 0x44, 0x3D, 0x00, // j
                         0x7F, 0x10, 0x28, 0x44, 0x00, // k
                         0x00, 0x41, 0x7F, 0x40, 0x00, // l
                         0x7C, 0x04, 0x78, 0x04, 0x78, // m
                         0x7C, 0x08, 0x04, 0x04, 0x78, // n
                         0x38, 0x44, 0x44, 0x44, 0x38, // o
                         0x7C, 0x14, 0x14, 0x14, 0x08, // p
                         0x08, 0x14, 0x14, 0x14, 0x7C, // q
                         0x00, 0x7C, 0x08, 0x04, 0x04, // r
                         0x48, 0x54, 0x54, 0x54, 0x20, // s
                         0x04, 0x04, 0x3F, 0x44, 0x44, // t
                         0x3C, 0x40, 0x40, 0x20, 0x7C, // u
                         0x1C, 0x20, 0x40, 0x20, 0x1C, // v
                         0x3C, 0x40, 0x30, 0x40, 0x3C, // w
                         0x44, 0x28, 0x10, 0x28, 0x44, // x
                         0x0C, 0x50, 0x50, 0x50, 0x3C, // y
                         0x44, 0x64, 0x54, 0x4C, 0x44, // z
                         0x00, 0x08, 0x36, 0x41, 0x41, // {
                         0x00, 0x00, 0x7F, 0x00, 0x00, // |
                         0x41, 0x41, 0x36, 0x08, 0x00, // }
                         0x02, 0x01, 0x02, 0x04, 0x02};// ~

/**
 * Strobes the Enable control line to trigger the lcd to process the
 * transmitted instruction.
 */
void lcd_strobe_enable(void) {
   output_high(GLCD_E);
   delay_us (3);
   output_low(GLCD_E);
   delay_us (3);   
}

/**
 * Waits for the busy flag to clear, which should take
 * around the maximum time for an instruction to complete.
 * Note, LCD operation is kind of sensitive to this configuration. If the delay
 * is too fast, the LCD will miss some pixels when it is really put through
 * a stress test. This delay time seems to work great.
 */
void lcd_wait_busy(void) {
   delay_us(3);
}

/**
 * Writes a command and data raw instruction to the LCD.
 * @param command The 4-bit instruction code.
 * @param data The 8-bit paramater/data to the specified instruction.
 */
void lcd_write_command(int8 command, int8 data) {
   /* Wait for the busy flag to clear */
   lcd_wait_busy();
   
   /* Set RW low, RS high, CS low to write the instruction command */
   output_low(GLCD_RW);
   output_high(GLCD_RS);
   output_low(GLCD_CS);

   output_d(command);
   delay_us (3);
   lcd_strobe_enable();
   delay_us (3);   

   /* Set RW low, RS low to write the instruction data */
   output_low(GLCD_RW);
   output_low(GLCD_RS);
   output_d(data);
   delay_us (3);
   lcd_strobe_enable();
   delay_us (3);
}

/**
 * Moves the LCD cursor to the specified coordinates.
 * @param x The new x coordinante of the cursor.
 * @param y The new y coordinante of the cursor.
 */
void lcd_graphics_move(int8 x, int8 y) {
   int16 pos;
   int8 LA, UA;

   /* Calculate the raw address in terms of bytes on the screen */
   pos = (_mul(y, LCD_WIDTH)+x)/8;
   LA = make8(pos, 0);
   UA = make8(pos, 1);
   
   /* Move the cursor to the new address */
   lcd_write_command(0x0A, LA);
   lcd_write_command(0x0B, UA);
}

// Purpose:       Turn a pixel on a graphic LCD on or off
// Inputs:        x - the x coordinate of the pixel
//                y - the y coordinate of the pixel
//                color - ON or OFF
// Output:        1 if coordinate out of range, 0 if in range
void glcd_pixel(int8 x, int8 y, short color)
{
   int16 pos;
   
   lcd_graphics_move(x, y);
   /* Since lcd_graphics_move() moves the cursor to a particular
    * byte, not bit, we need the relative distance to the specified
    * bit we are going to set/clear. */
   pos = x%8;

   if (color == ON)
      lcd_write_command(0x0F, pos);
   else
      lcd_write_command(0x0E, pos);
}

// Purpose:       Draw a line on a graphic LCD using Bresenham's
//                line drawing algorithm
// Inputs:        (x1, y1) - the start coordinate
//                (x2, y2) - the end coordinate
//                color - ON or OFF
// Dependencies:  glcd_pixel()
void glcd_line(int8 x1, int8 y1, int8 x2, int8 y2, short color)
{
   signed int8  x, y, addx, addy, dx, dy;
   signed long P;
   int8 i;
   dx = abs((signed int8)(x2 - x1));
   dy = abs((signed int8)(y2 - y1));
   x = x1;
   y = y1;

   if(x1 > x2)
      addx = -1;
   else
      addx = 1;
   if(y1 > y2)
      addy = -1;
   else
      addy = 1;

   if(dx >= dy)
   {
      P = 2*dy - dx;

      for(i=0; i<=dx; ++i)
      {
         glcd_pixel(x, y, color);

         if(P < 0)
         {
            P += 2*dy;
            x += addx;
         }
         else
         {
            P += 2*dy - 2*dx;
            x += addx;
            y += addy;
         }
      }
   }
   else
   {
      P = 2*dx - dy;

      for(i=0; i<=dy; ++i)
      {
         glcd_pixel(x, y, color);

         if(P < 0)
         {
            P += 2*dx;
            y += addy;
         }
         else
         {
            P += 2*dx - 2*dy;
            x += addx;
            y += addy;
         }
      }
   }
}

// Purpose:       Draw a rectangle on a graphic LCD
// Inputs:        (x1, y1) - the start coordinate
//                (x2, y2) - the end coordinate
//                fill  - YES or NO
//                color - ON or OFF
// Dependencies:  glcd_pixel(), glcd_line()
void glcd_rect(int8 x1, int8 y1, int8 x2, int8 y2, short fill, short color)
{
   if(fill)
   {
      int8 y, ymax;                          // Find the y min and max
      if(y1 < y2)
      {
         y = y1;
         ymax = y2;
      }
      else
      {
         y = y2;
         ymax = y1;
      }

      for(; y<=ymax; ++y)                    // Draw lines to fill the rectangle
         glcd_line(x1, y, x2, y, color);
   }
   else
   {
      glcd_line(x1, y1, x2, y1, color);      // Draw the 4 sides
      glcd_line(x1, y2, x2, y2, color);
      glcd_line(x1, y1, x1, y2, color);
      glcd_line(x2, y1, x2, y2, color);
   }
}


// Purpose:       Draw a bar (wide line) on a graphic LCD
// Inputs:        (x1, y1) - the start coordinate
//                (x2, y2) - the end coordinate
//                width  - The number of pixels wide
//                color - ON or OFF
void glcd_bar(int8 x1, int8 y1, int8 x2, int8 y2, int8 width, short color)
{
   signed int8  x, y, addx, addy, j;
   signed long P, dx, dy, c1, c2;
   int8 i;
   dx = abs((signed int8)(x2 - x1));
   dy = abs((signed int8)(y2 - y1));
   x = x1;
   y = y1;
   c1 = -dx*x1 - dy*y1;
   c2 = -dx*x2 - dy*y2;

   if(x1 > x2)
   {
      addx = -1;
      c1 = -dx*x2 - dy*y2;
      c2 = -dx*x1 - dy*y1;
   }
   else
      addx = 1;
   if(y1 > y2)
   {
      addy = -1;
      c1 = -dx*x2 - dy*y2;
      c2 = -dx*x1 - dy*y1;
   }
   else
      addy = 1;

   if(dx >= dy)
   {
      P = 2*dy - dx;

      for(i=0; i<=dx; ++i)
      {
         for(j=-(width/2); j<width/2+width%2; ++j)
         {
            if(dx*x+dy*(y+j)+c1 >= 0 && dx*x+dy*(y+j)+c2 <=0)
               glcd_pixel(x, y+j, color);
         }
         if(P < 0)
         {
            P += 2*dy;
            x += addx;
         }
         else
         {
            P += 2*dy - 2*dx;
            x += addx;
            y += addy;
         }
      }
   }
   else
   {
      P = 2*dx - dy;

      for(i=0; i<=dy; ++i)
      {
         if(P < 0)
         {
            P += 2*dx;
            y += addy;
         }
         else
         {
            P += 2*dx - 2*dy;
            x += addx;
            y += addy;
         }
         for(j=-(width/2); j<width/2+width%2; ++j)
         {
            if(dx*x+dy*(y+j)+c1 >= 0 && dx*x+dy*(y+j)+c2 <=0)
               glcd_pixel(x+j, y, color);
         }
      }
   }
}

// Purpose:       Draw a circle on a graphic LCD
// Inputs:        (x,y) - the center of the circle
//                radius - the radius of the circle
//                fill - YES or NO
//                color - ON or OFF
void glcd_circle(int8 x, int8 y, int8 radius, short fill, short color)
{
   signed int8 a, b, P;
   a = 0;
   b = radius;
   P = 1 - radius;

   do
   {
      if(fill)
      {
         glcd_line(x-a, y+b, x+a, y+b, color);
         glcd_line(x-a, y-b, x+a, y-b, color);
         glcd_line(x-b, y+a, x+b, y+a, color);
         glcd_line(x-b, y-a, x+b, y-a, color);
      }
      else
      {
         glcd_pixel(a+x, b+y, color);
         glcd_pixel(b+x, a+y, color);
         glcd_pixel(x-a, b+y, color);
         glcd_pixel(x-b, a+y, color);
         glcd_pixel(b+x, y-a, color);
         glcd_pixel(a+x, y-b, color);
         glcd_pixel(x-a, y-b, color);
         glcd_pixel(x-b, y-a, color);
      }

      if(P < 0)
         P+= 3 + 2*a++;
      else
         P+= 5 + 2*(a++ - b--);
    } while(a <= b);
}

// Purpose:       Write text on a graphic LCD
// Inputs:        (x,y) - The upper left coordinate of the first letter
//                textptr - A pointer to an array of text to display
//                size - The size of the text: 1 = 5x7, 2 = 10x14, ...
//                color - ON or OFF
void glcd_text57(int8 x, int8 y, char* textptr, int8 size, short color)
{
   int8 i, j, k, l, m;                     // Loop counters
   int8 pixelData[5];                     // Stores character data
   for(i=0; textptr[i] != '\0'; ++i, ++x) // Loop through the passed string
   {
      if(textptr[i] < 'S') // Checks if the letter is in the first text array
         memcpy(pixelData, TEXT[textptr[i]-' '], 5);
      else if(textptr[i] <= '~') // Check if the letter is in the second array
         memcpy(pixelData, TEXT2[textptr[i]-'S'], 5);
      else
         memset(pixelData, ' ', 5);   // Default to space

      if(x+5*size >= LCD_WIDTH)          // Performs character wrapping
      {
         x = 0;                           // Set x at far left position
         y += 8*size + 1;                 // Set y at next position down
      }
      for(j=0; j<5; ++j, x+=size)         // Loop through character byte data
      {
         for(k=0; k<8*size; ++k)          // Loop through the vertical pixels
         {
            if(bit_test(pixelData[j], k)) // Check if the pixel should be set
            {
               for(l=0; l<size; ++l)      // The next two loops change the
               {                          // character's size
                  for(m=0; m<size; ++m)
                  {
                     glcd_pixel(x+m, y+k*size+l, color); // Draws the pixel
                  }
               }
            }
            else
            {
               for(l=0; l<size; ++l)      // The next two loops change the
               {                          // character's size
                  for(m=0; m<size; ++m)
                  {
                     glcd_pixel(x+m, y+k*size+l, 0); // Clears the pixel
                  }
               }
            }
         }
      }
   }
}

/**
 * Draws a byte to the LCD at the current LCD's cursor location.
 * @param data The byte to draw. The pixels are drawn MSB to LSB.
 */
void lcd_graphics_draw_byte(int8 data) {
   lcd_write_command(0x0C, data);
}

/**
 * Plots a byte at the specified coordinates.
 * @param x The x coordinante of the byte to be drawn.
 * @param y The y coordinante of the byte to be drawn.
 * @param data The byte to draw. The pixels are drawn MSB to LSB.
 */
void lcd_graphics_plot_byte(int8 x, int8 y, int8 data) {
   lcd_graphics_move(x, y);
   lcd_graphics_draw_byte(data);
}

// Purpose:       Fill the LCD screen with the passed in color.
//                Works much faster than drawing a rectangle to fill the screen.
// Inputs:        ON - turn all the pixels on
//                OFF - turn all the pixels off
// Dependencies:  glcd_writeByte()
void glcd_fillScreen(short mode)
{
   long i;
   /* Move cursor to home (top left corner) */
   lcd_graphics_move(0, 0);
   /* Draw empty bytes to ocucpy the entire screen */
   for (i = 0; i < ((LCD_WIDTH*LCD_HEIGHT)/8); i++)
      if (mode == OFF)
         lcd_graphics_draw_byte(PIXEL_OFF);
      else
         lcd_graphics_draw_byte(PIXEL_ON);
}

// Purpose:       Reads a byte of data from the specified chip
// Ouputs:        A byte of data read from the chip
int8 glcd_readByte(int8 chip)
{
   int8 data;                 // Stores the data read from the LCD
   lcd_write_command(0x0D, 0x00);
   output_low(GLCD_CS);
   output_high(GLCD_RW);      // Set for reading
   input_d();                 // Set port d to input
   output_high(GLCD_E);       // Pulse the enable pin
   delay_us(2);
   output_low(GLCD_E);
   delay_us(2);
   output_high(GLCD_E);       // Pulse the enable pin
   delay_us(2);
   output_low(GLCD_E);
   delay_us(2);
   data = input_d();          // Get the data from the display's output register

   output_low(GLCD_CS);      // Reset the chip select lines
   return data;               // Return the read data
}

// Purpose:       Initialize a graphic LCD. This must be called before any
//                other glcd function is used.
// Inputs:        The initialization mode
//                OFF - Turns character mode ON
//                ON  - Turns graphic mode ON
// Date:          5/28/2003
void glcd_init(short mode)
{
   // Initialze some pins
   output_low(GLCD_RST);
   output_low(GLCD_E);
   output_low(GLCD_RS);
   output_high(GLCD_CS);
   output_d(0x0);
   delay_ms(1);
   output_high(GLCD_RST);
   delay_ms(1);

   if(mode == ON)
   {
   lcd_write_command(0x00, 0x32);
   lcd_write_command(0x01, 0x77);
   }
   else
   {
   lcd_write_command(0x00, 0x3C);
   lcd_write_command(0x01, 0x97);
   }
   lcd_write_command(0x02, 19);
   lcd_write_command(0x03, 100);
   lcd_write_command(0x04, 0x07);
   lcd_write_command(0x08, 0x00);
   lcd_write_command(0x09, 0x00);
   lcd_write_command(0x0A, 0x00);
   lcd_write_command(0x0B, 0x00);

   glcd_fillScreen(OFF);               // Clear the display
}

//
void glcd_blank(short mode) {
  if(mode == ON) {
      output_high(GLCD_ON);           // Turn the display on
   }
   else
   {
      output_low(GLCD_ON);           // Turn the display off
   }
}

// glcd_pixel8(x,y,px8) sets or clears 8 pixels in line at x,y
void glcd_pixel8(int8 x, int8 y, int8 pixel8) {
   lcd_graphics_move(x+1,y);
   lcd_write_command(0x0c, pixel8);
}

//glcd_image8 (*Pic, x, y, size_x, size_y)
void glcd_image8(int8 *pic_px, int8 x, int8 y,
                 int8 size_x, int8 size_y) {
   int8 px_y;
   int8 px_x;
   int8 px=0;

   for(px_y=y; px_y<(y+size_y); px_y++) {
      for(px_x=x; px_x<(x+size_x); px_x+=8) {
         glcd_pixel8(px_x, px_y, *(pic_px+px));
         px+=1;
      }
   }
}

//
void glcd_text8x8(char *Pix, int8 line) {
int8 i;                     // Loop counters
char pixelData[8];

   for(i=0; i<20; ++i) // Loop through the passed string
   {
//      if(textptr[i] < 'S') // Checks if the letter is in the first text array
//         memcpy(pixelData, TEXT[textptr[i]-' '], 5);
//      else if(textptr[i] <= '~') // Check if the letter is in the second array
//         memcpy(pixelData, TEXT2[textptr[i]-'S'], 5);
//      else
//         memset(pixelData, ' ', 5);   // Default to space

      if(Pix[i] < '4') // Checks if the letter is in the first text array
         memcpy(pixelData, TEXTA[Pix[i]-' '], 8);
      else if(Pix[i] < 'H') // Check if the letter is in the second array
         memcpy(pixelData, TEXTB[Pix[i]-'4'], 8);
      else if(Pix[i] < ('\\')) // Check if the letter is in the second array
         memcpy(pixelData, TEXTC[Pix[i]-'H'], 8);
      else if(Pix[i] < 'p') // Check if the letter is in the second array
         memcpy(pixelData, TEXTD[Pix[i]-'\\'], 8);
      else if(Pix[i] <= 0x7F) // Check if the letter is in the second array
         memcpy(pixelData, TEXTE[Pix[i]-'p'], 8);
      else {
         memcpy(pixelData, TEXTA[0], 8);   // Default to space
      }
      glcd_image8(pixelData, i*8, line*10, 8, 8);
   }
}

//
void move_char(int8 x, int8 y) {
   int16 pos;
   int8 LA, UA;

   /* Calculate the raw address in terms of characters on the screen */
   pos = (_mul(y, 20)+x);
   LA = make8(pos, 0);
   UA = make8(pos, 1);
   
   /* Move the cursor to the new address */
   lcd_write_command(0x0A, LA);
   lcd_write_command(0x0B, UA);
}

//
void glcd_char(int8 x, int8 y, char* textptr) {
int8 i;

   move_char(x, y);
   for(i=0; i<20; i++) {
      lcd_write_command(0x0c, textptr[i]);
   }
}

//
void char_fillScreen(short mode) {
   long i;
   /* Move cursor to home (top left corner) */
   move_char(0, 0);
   /* Draw blank or filled chars to ocucpy the entire screen */
   for (i = 0; i < 160; i++)
      if (mode == OFF)
         lcd_write_command(0x0c, 0x20);
      else
         lcd_write_command(0x0c, 0xFF);
}
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> Code Library All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group