CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

External Interrupt

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
Bieli
Guest







External Interrupt
PostPosted: Tue Jan 14, 2003 12:41 am     Reply with quote

In this program the led should blinking every one second. The signal is taken from real time clock. But it blinked 8 sometimes 2 or 4 times and after it it stop. The low level is puted on RB0, but the interrupt don't delete it ( WRITE_PCF8583( 00, 04 ); ) so propably the interrupt isn't taken.
The problem can be coused that I use 16F874.h and 16F874A chip <- Is this problem or my code is wrong?

#include <16f874.h>
#fuses HS,NOWDT,NOPROTECT,NOLVP
#use delay(clock=4000000)
#include <b_lcd.c>

#define EEPROM_SDA PIN_C2
#define EEPROM_SCL PIN_C3

#include <PCF8583.c>

#int_ext
Przerwanie_T1()
{ output_bit(pin_d0,!input(pin_d0)); //Blinking led
WRITE_PCF8583( 00, 04 ); //Delete interrupt flag in PCF8583
}
main() {

enable_interrupts(global);
enable_interrupts(INT_EXT);
EXT_INT_EDGE(H_TO_L);
init_PCF8583();
lcd_init();

.....

do {
printf(lcd_putc,"\f\%X:\%X:\%X\n \%X-\%X \%X",READ_PCF8583(04),READ_PCF8583(03),READ_PCF8583(02),READ_PCF8583(05),READ_PCF8583(06),READ_PCF8583(00));
} while (TRUE);

}
___________________________
This message was ported from CCS's old forum
Original Post ID: 10673
kolio
Guest







Re: External Interrupt
PostPosted: Tue Jan 14, 2003 2:16 am     Reply with quote

Hi,
What will happen while execution of endless loop readings READ_PCF8583(xx) there appears an interrupt from RTC and in the middle of one reading at I2C bus ISR starts to write to RTC?
I don't know if at READ_PCF8583() the interrupts are previously disabled in order to avoid collisions, but you should prevent the asynchronous reference to RTC.
You can put TF clearing outside of ISR, like this:

short TF;
#int_ext
Przerwanie_T1()
{ output_bit(pin_d0,!input(pin_d0)); //Blinking led
TF = 1;
}
main() {

enable_interrupts(global);
enable_interrupts(INT_EXT);
EXT_INT_EDGE(H_TO_L);
init_PCF8583();
lcd_init();
TF = 0;

.....

do {
if(TF) {
WRITE_PCF8583( 00, 04 ); //Delete interrupt flag in PCF8583
TF = 0;
}
printf(lcd_putc,"\f\%X:\%X:\%X\n \%X-\%X \%X",READ_PCF8583(04),READ_PCF8583(03),READ_PCF8583(02),READ_PCF8583(05),READ_PCF8583(06),READ_PCF8583(00));
} while (TRUE);

}


According to me you shouldn't worry too much about the versions 874 and 874A.
Wish you luck!
___________________________
This message was ported from CCS's old forum
Original Post ID: 10677
Tomi
Guest







Re: External Interrupt
PostPosted: Tue Jan 14, 2003 2:19 am     Reply with quote

How do you attach the LED to D0 bit? Keep in mind that the input() function reads the pin so it could be 0 even if the LED lights. Additional problem that the input() function sets that pin to input first then the output_bit() function sets back it to output.
It would be better to use a RAM flag to set/reset it and then copy its state to pin_D0.

:=In this program the led should blinking every one second. The signal is taken from real time clock. But it blinked 8 sometimes 2 or 4 times and after it it stop. The low level is puted on RB0, but the interrupt don't delete it ( WRITE_PCF8583( 00, 04 ); ) so propably the interrupt isn't taken.
:=The problem can be coused that I use 16F874.h and 16F874A chip <- Is this problem or my code is wrong?
:=
:=#include <16f874.h>
:=#fuses HS,NOWDT,NOPROTECT,NOLVP
:=#use delay(clock=4000000)
:=#include <b_lcd.c>
:=
:=#define EEPROM_SDA PIN_C2
:=#define EEPROM_SCL PIN_C3
:=
:=#include <PCF8583.c>
:=
:=#int_ext
:=Przerwanie_T1()
:={ output_bit(pin_d0,!input(pin_d0)); //Blinking led
:= WRITE_PCF8583( 00, 04 ); //Delete interrupt flag in PCF8583
:=}
:=main() {
:=
:= enable_interrupts(global);
:= enable_interrupts(INT_EXT);
:= EXT_INT_EDGE(H_TO_L);
:= init_PCF8583();
:= lcd_init();
:=
:= .....
:=
:= do {
:= printf(lcd_putc,"\f\%X:\%X:\%X\n \%X-\%X \%X",READ_PCF8583(04),READ_PCF8583(03),READ_PCF8583(02),READ_PCF8583(05),READ_PCF8583(06),READ_PCF8583(00));
:= } while (TRUE);
:=
:=}
___________________________
This message was ported from CCS's old forum
Original Post ID: 10678
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group