CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
Ready to give up with CCS's i2c slave libraries

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
valemike
Guest
Ready to give up with CCS's i2c slave libraries
PostPosted: Mon May 10, 2004 3:42 pm     Reply with quote
I'm trying to implement a Slave hardware I2C. Even Microchip's FAEs say there are issues with CCS's slave i2c, as i read the same here every now now and then also.

Looking at this sample code, from the Master:

Code:

#include <18F252.h>
#fuses HS,NOWDT,NOPROTECT,NOLVP
#use delay(clock=4000000)

#use i2c(Master,sda=PIN_C4,scl=PIN_C3)
void main()
{
    byte incoming;

   while (1)
   {
       i2c_start();
       i2c_write(0xa0); //slave can read.
       i2c_write(incoming);
       i2c_write(5); 
       i2c_write(0x01); // slave can write.
      delay_ms(1);
   
//   if (i2c_poll())
//   {
       incoming = i2c_read();
       incoming = i2c_read();
//   }
   
//   i2c_stop();
   }
}


As you can see, I commented out the i2c_poll() and the i2c_stop, and just keep looping. When I try to issue an i2c_read() at the master, then it causes the slave to trigger an i2c_read() of 0xFF.

Is the i2c_read() up above supposed to block until the slave issues an i2c_write()? I don't seem to see that happening.

I don't know if CCS's i2c library (especially for PICs acting as i2c slaves) is robust, and i'm ready to ditch using the library and instead manipulating the the control registers directly.

Here's the slave code below. heck for some reason, i can't seem to get an i2c_poll() to return a TRUE when issuing an i2c_read() shortly after the master issued an i2c_start(). So i figure, the heck with the i2c_poll(), and just do an i2c_read() everytime i get an SSP interrupt. That seems to work just fine for reads, but then i can't do a write. oh well.
Haplo



Joined: 06 Sep 2003
Posts: 659
Location: Sydney, Australia

View user's profile Send private message

PostPosted: Mon May 10, 2004 5:30 pm     Reply with quote
er...you forgot to post the slave code.
Darren Rook



Joined: 06 Sep 2003
Posts: 287
Location: Milwaukee, WI

View user's profile Send private message Send e-mail

PostPosted: Mon May 10, 2004 6:40 pm     Reply with quote
Use FORCE_HW, else it's using SW on the master.
Darren Rook



Joined: 06 Sep 2003
Posts: 287
Location: Milwaukee, WI

View user's profile Send private message Send e-mail

Re: Ready to give up with CCS's i2c slave libraries
PostPosted: Mon May 10, 2004 7:03 pm     Reply with quote
valemike wrote:

Is the i2c_read() up above supposed to block until the slave issues an i2c_write()? I don't seem to see that happening.


Yes, in hardware mode i2c_read() sets the RCEN bit in SSPCON2 and then waits indefinately until RCEN is cleared by hardware. RCEN is cleared by hardware when it receives a byte.

If you're so convinced that it's CCS's fault how about some proof?
valemike
Guest
slave and master code
PostPosted: Tue May 11, 2004 8:52 am     Reply with quote
I apologize yesterday for quickly pointing the finger at CCS's i2c library. With so many different scenarios, there is no way their example code can exactly fit a programmer's needs unless the programmer understanding what is going on.

Anyways, I tried using FORCE_HW at the master. Here is the example code:

master:
Code:

#include <18F252.h>
#fuses HS,NOWDT,NOPROTECT,NOLVP
#use delay(clock=4000000)

#use i2c(Master,sda=PIN_C4,scl=PIN_C3, FORCE_HW)
void main()
{
    byte incoming;

   while (1)
   {
       i2c_start();
       i2c_write(0xa0); //slave can read.
      delay_ms(100);
      i2c_write(5);
      delay_ms(100);
      i2c_write(0x01); // slave can write.
   
      while (i2c_poll() == FALSE)
     {
     }
   
     incoming = i2c_read();
   
     i2c_stop();
   }
}


And the SLAVE code:

Code:

#include <18F452.h>
#fuses HS,NOWDT,NoPROTECT,NOLVP
#use delay(clock=4000000)
#use rs232(baud=9600, xmit=PIN_C6, rcv=PIN_C7, ERRORS)
#use I2C(slave, sda=PIN_C4, scl=PIN_C3, address=0xa0, FORCE_HW)

typedef enum
{
     ADDRESS_READ,
     DATA_READ
} I2C_STATE;

I2C_STATE fState;
BYTE address, buffer[0x10];

volatile int flag;
byte incoming;

#INT_SSP
void i2c_slave_handler(void)
{   
    incoming = i2c_read();
    flag = 1;       
}

void main(void)
{
    int i;
    flag = 0;
    fState = ADDRESS_READ;
       
    for (i=0; i<0x10; i++)
        buffer[i] = 0x00;
       
    enable_interrupts(INT_SSP);
    enable_interrupts(GLOBAL);

    printf ("Start i2c slave\r\n");

    while (1)
    {
        if (flag == 1)
        {
            printf ("incoming = 0x%2.2X\r\n", incoming);
            flag = 0;
           
            if (incoming == 0x01)
            {
                i2c_write(0x01);
                flag = 0;
            }
        }
    }
}


The output on Hyperterminal looks like this:
Code:

Start i2c slave
incoming = 0xA0
incoming = 0x05
incoming = 0x01


I have a ICE2000 running on the master. I see that it never gets past the while (i2c_poll() == FALSE). I have ICD-2 running on the slave. I see that it does get past the i2c_write() when incoming == 0x01. However, the Master never sees its i2c_poll go TRUE.

This is getting really frustrating. Mad
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group