CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

Compiler error with modbus driver

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
pebbert9



Joined: 31 Dec 2010
Posts: 36

View user's profile Send private message

Compiler error with modbus driver
PostPosted: Mon Sep 21, 2020 6:24 pm     Reply with quote

Hello,

I am trying to get this sample code below to compile but it is giving me errors

Using 5.094

*** Error 28 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer.h" Line 78(44,45): Expecting an identifier Bad SFR name
*** Error 12 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer.h" Line 99(8,11): Undefined identifier
*** Error 48 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer.h" Line 99(12,16): Expecting a (
*** Error 48 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer.h" Line 99(17,22): Expecting a (
--- Info 300 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer_rtu.c" Line 25(1,1): More info: Timer 1 tick time is 128.00 us
*** Error 12 "C:\Program Files (x86)\PICC\Drivers\modbus_phy_layer_rtu.c" Line 317(24,25): Undefined identifier TRMT


Code:
#include <18F25K83.h>
#device ADC=12

#FUSES NOWDT                    //No Watch Dog Timer

#use delay(clock=32000000,crystal=8000000)

#define MODBUS_BUS SERIAL
#define MODBUS_TYPE MODBUS_TYPE_SLAVE
#define MODBUS_SERIAL_TYPE MODBUS_RTU
#define MODBUS_SERIAL_INT_SOURCE MODBUS_INT_RDA
#define MODBUS_SERIAL_RX_PIN PIN_C6
#define MODBUS_SERIAL_TX_PIN PIN_C4
#define MODBUS_SERIAL_ENABLE_PIN PIN_C5
#define MODBUS_SERIAL_BAUD 115200
#define MODBUS_OUR_ADDRESS 15

#pin_select U1RX=MODBUS_SERIAL_RX_PIN
#pin_select U1TX=MODBUS_SERIAL_TX_PIN

#include "modbus.c"

void main()
{
   modbus_init();

   while(TRUE)
   {


      //TODO: User Code
   }

}


Any ideas?

Thanks
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Tue Sep 22, 2020 12:41 am     Reply with quote

Substitute this block of code for lines 56 through 107 in the
modbus_phy_layer.h file. This is for CCS vs. 5.095.
It will now compile without errors. These changes may not
be sufficient to make it work, because the UART in the 18F25K83
is significantly different than in the 18F46K22. But at least it
will now compile.
Code:

#if (MODBUS_SERIAL_INT_SOURCE != MODBUS_INT_EXT)
   #if defined(__PCD__)
      #if (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA)
         #word TXSTA=getenv("SFR:U1STA")
         #bit TRMT=TXSTA.8
      #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA2)
         #word TXSTA=getenv("SFR:U2STA")
         #bit TRMT=TXSTA.8
      #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA3)
         #word TXSTA=getenv("SFR:U3STA")
         #bit TRMT=TXSTA.8
      #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA4)
         #word TXSTA=getenv("SFR:U4STA")
         #bit TRMT=TXSTA.8
      #endif
   #else
      #if (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA)
         #if getenv("sfr_valid:U1ERRIR")       // *** Add this line ***
             #byte TXSTA=getenv("sfr:U1ERRIR") // *** Add this line ***
         #elif getenv("sfr_valid:TXSTA")       // *** Change to #elif ***
            #byte TXSTA=getenv("sfr:TXSTA")
         #elif getenv("sfr_valid:TXSTA1")
            #byte TXSTA=getenv("sfr:TXSTA1")
         #else
            #byte TXSTA=getenv("sfr:TX1STA")
         #endif
      #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA2)
         #if getenv("sfr_valid:TXSTA2")
            #byte TXSTA=getenv("sfr:TXSTA2")
         #else
            #byte TXSTA=getenv("sfr:TX2STA")
         #endif
     #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA3)
         #if getenv("sfr_valid:TXSTA3")
            #byte TXSTA=getenv("sfr:TXSTA3")
         #else
            #byte TXSTA=getenv("sfr:TX3STA")
         #endif
     #elif (MODBUS_SERIAL_INT_SOURCE == MODBUS_INT_RDA4)
         #if getenv("sfr_valid:TXSTA4")
            #byte TXSTA=getenv("sfr:TXSTA4")
         #else
            #byte TXSTA=getenv("sfr:TX4STA")
         #endif
      #endif
      #if getenv("sfr_valid:U1ERRIR") // *** Add this line ***
          #bit TRMT=TXSTA.7 // *** Add this line ***
      #else                 // *** Add this line ***
          #bit TRMT=TXSTA.1
      #endif                // *** Add this line ***
   #endif
#endif
pebbert9



Joined: 31 Dec 2010
Posts: 36

View user's profile Send private message

PostPosted: Tue Sep 22, 2020 11:09 am     Reply with quote

Thanks for your help.

The 18F25K83 does appear to be working now.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group