CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug Reports on this forum. Send them to support@ccsinfo.com

Can't read device ID

 
Post new topic   Reply to topic    CCS Forum Index -> CCS ICD / Mach X / Load-n-Go
View previous topic :: View next topic  
Author Message
Jampe



Joined: 09 Mar 2012
Posts: 27

View user's profile Send private message

Can't read device ID
PostPosted: Thu Dec 19, 2013 9:37 am     Reply with quote

Hi everyone,
I'm trying to connect my controller (PIC16F887) to my PC (with ICD-U64) and this is the error i receive :



There I see :



I've tried to update my firmware to 3.01 but without success...
What can I do to make it works?
By the way, my second controller (PIC16F877A) is the same I tried on my laptop and it connected to 9Volt.
Thanks for you help!
PCM programmer



Joined: 06 Sep 2003
Posts: 20256

View user's profile Send private message

PostPosted: Thu Dec 19, 2013 12:14 pm     Reply with quote

Read this thread. It's a 2-page thread. It has some possible fixes for
the CCSload "access violation" problem:
http://www.ccsinfo.com/forum/viewtopic.php?t=43576
Jampe



Joined: 09 Mar 2012
Posts: 27

View user's profile Send private message

PostPosted: Thu Dec 19, 2013 1:40 pm     Reply with quote

PCM programmer wrote:
Read this thread. It's a 2-page thread. It has some possible fixes for
the CCSload "access violation" problem:
http://www.ccsinfo.com/forum/viewtopic.php?t=43576

Thank you for your rapidly reply.
I tried this :

Quote:
To fix it I had to
1) Uninstall CCSload.
2) Keep ICD-U64/ICD-U40 plugged in. If it isn't go ahead and plug it in.
I'm assuming USB and Windows XP.
3) Go to System Properties -> Device Manager -> Universal Serial Bus
controllers and delete CCS ICD-U64 entry.
4) Now unplug ICD-U64 from the USB.
5) Run Ccleaner to clear out unused Reg. Entries.
5) Reboot.
6) Install ICD-U64 drivers.
7) Install CCSload


and this :

Quote:
There is an easy fix for CCSload pointing to the wrong file. You'll need to open the pcw.ini file in a text editor.

Search for [ProgrammerFiles] and delete the name of the bad file. Save and exit, then start CCSload.


still doesn't work..
any ideas?
PCM programmer



Joined: 06 Sep 2003
Posts: 20256

View user's profile Send private message

PostPosted: Thu Dec 19, 2013 4:35 pm     Reply with quote

Email CCS support and ask them what to do. Give them a link to
this thread. Give them your name and your CCS user number.
Jampe



Joined: 09 Mar 2012
Posts: 27

View user's profile Send private message

PostPosted: Thu Dec 19, 2013 6:13 pm     Reply with quote

PCM programmer wrote:
Email CCS support and ask them what to do. Give them a link to
this thread. Give them your name and your CCS user number.

I will thank you a lot!
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> CCS ICD / Mach X / Load-n-Go All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group