CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug Reports on this forum. Send them to support@ccsinfo.com

PIC 16F84A Development Breadboard

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
Regular Guy



Joined: 04 Jun 2017
Posts: 67

View user's profile Send private message

PIC 16F84A Development Breadboard
PostPosted: Tue Nov 03, 2020 4:07 pm     Reply with quote

Putting together hardware for our assembler lessons.

Using 32khz crystal and 68p capacitors.

Two 840 hole breadboards. Connected together.

QUESTION

Are you supposed to work on it with breadboards sideways or straight up

and down?

We have been keeping them straight up and down. The letters and numbers

on them go that way.

Have seen a lot of pictures over the years with the breadboards sideways.

Thanks! Smile
_________________
PCB Compiler

Development Kits:

DSP Starter Early version PCB board ICD-S40 no plastic case

Rapid USB Prototyping Stick

Sensor Explorer

E3 Mini Board Book & Board Bundle

16F877A
temtronic



Joined: 01 Jul 2010
Posts: 7686
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Tue Nov 03, 2020 5:05 pm     Reply with quote

whatever works for you, there is not 'right or wrong'.
I have one in front of me, horizontal as the LCD module hangs off the lower right corner. above it is the TTLUSB module and a combo RTC/EEP module. To the left is the 18F46k22 ,and furthest left the ICSP connections.
Regular Guy



Joined: 04 Jun 2017
Posts: 67

View user's profile Send private message

PostPosted: Tue Nov 03, 2020 5:21 pm     Reply with quote

Code:
; HEADER84.ASM for 16F84. This sets PORTA as an INPUT (NB 1means
input).
; and PORTB as an OUTPUT (NB 0 means output).
;The OPTION Register is set to /256 to give timing pulses of 1/32 of a second.
;1second and 0.5 second delays are included in the subroutine section.

 list      p=16F84A             ; list directive to define processor
    #include <p16F84a.inc>         ; processor specific variable definitions

    __CONFIG   _CP_OFF & _WDT_ON & _PWRTE_ON & _RC_OSC

RESET_VECTOR      CODE    0x0000  ; processor reset vector
        goto    start             ; go to beginning of program

MAIN_PROGRAM    CODE

start:

; remaining code goes here

;CONFIGURATION SECTION
START BSF STATUS,5 ;Turns to Bank1.
MOVLW B’00011111’ ;5bits of PORTA are I/P
MOVWF TRISA
MOVLW B’00000000’
MOVWF TRISB ;PORTB is OUTPUT
MOVLW B’00000111’ ;Prescaler is /256
MOVWF OPTION_R ;TIMER is 1/32 secs.
BCF STATUS,5 ;Return to Bank0.
CLRF PORTA ;Clears PortA.
CLRF PORTB ;Clears PortB.
;*********************************************************
;Program starts now.

        goto $

        END                       ; directive 'end of program'

_________________
PCB Compiler

Development Kits:

DSP Starter Early version PCB board ICD-S40 no plastic case

Rapid USB Prototyping Stick

Sensor Explorer

E3 Mini Board Book & Board Bundle

16F877A
Regular Guy



Joined: 04 Jun 2017
Posts: 67

View user's profile Send private message

PostPosted: Tue Nov 03, 2020 5:23 pm     Reply with quote

Thanks Jay

Posted code for our header file.

Which we will use in each new program.

Ignore the bunched up Configuration section.

That is from copying from Adobe Acrobat .PDF

We have become experts at tabbing.

Thanks!
_________________
PCB Compiler

Development Kits:

DSP Starter Early version PCB board ICD-S40 no plastic case

Rapid USB Prototyping Stick

Sensor Explorer

E3 Mini Board Book & Board Bundle

16F877A
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group