CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

RN2903 Wake up

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
cvargcal



Joined: 17 Feb 2015
Posts: 134

View user's profile Send private message

RN2903 Wake up
PostPosted: Wed Mar 21, 2018 4:30 pm     Reply with quote

Hi I need Wake up this module, but I can not get...
The manual say its necessary a "break condition" how I can do?
http://ww1.microchip.com/downloads/en/DeviceDoc/40001811A.pdf


for sleep module
Code:
 fprintf(lora,"sys sleep 40000\r\n");   // // Enter sleep mode for 40 seconds


for wake up

Code:
output_low(TXD_Lora);   // Start break signal on MCU TX pin
delay_ms(1000);;               
 output_high(TXD_Lora);   // Start break signal on MCU TX pin
 fprintf(lora, 0x55);          // Send magic break character (auto bauding)



But not work
asmallri



Joined: 12 Aug 2004
Posts: 1634
Location: Perth, Australia

View user's profile Send private message Send e-mail Visit poster's website

PostPosted: Wed Mar 21, 2018 4:38 pm     Reply with quote

This would not create a break condition because the uart is mapped to the serial port. To use this mechanism you would need to close the serial port, send your break, then open the serial port.

Alternatively, you could wake the module via toggling the reset line. This is the mechanism I use.
_________________
Regards, Andrew

http://www.brushelectronics.com/software
Home of Ethernet, SD card and Encrypted Serial Bootloaders for PICs!!
cvargcal



Joined: 17 Feb 2015
Posts: 134

View user's profile Send private message

PostPosted: Wed Mar 21, 2018 5:07 pm     Reply with quote

asmallri wrote:
This would not create a break condition because the uart is mapped to the serial port. To use this mechanism you would need to close the serial port, send your break, then open the serial port.

Alternatively, you could wake the module via toggling the reset line. This is the mechanism I use.


Thanks, I use that PIN RESET, but I did many PCB and not put that wire...because I need wake up and not Reset
asmallri



Joined: 12 Aug 2004
Posts: 1634
Location: Perth, Australia

View user's profile Send private message Send e-mail Visit poster's website

PostPosted: Wed Mar 21, 2018 6:38 pm     Reply with quote

You need the CCS equivalent of this:

Code:

void wakeUP_RN2483() {
    Serial1.end();
    pinMode(PIN_SERIAL1_TX, OUTPUT);
    digitalWrite(PIN_SERIAL1_TX, LOW);
    delay(5);
    digitalWrite(PIN_SERIAL1_TX, HIGH);
    Serial1.begin(57600);
    Serial1.write(0x55);
}

_________________
Regards, Andrew

http://www.brushelectronics.com/software
Home of Ethernet, SD card and Encrypted Serial Bootloaders for PICs!!
cvargcal



Joined: 17 Feb 2015
Posts: 134

View user's profile Send private message

PostPosted: Wed Mar 21, 2018 11:46 pm     Reply with quote

asmallri wrote:
You need the CCS equivalent of this:

Code:

void wakeUP_RN2483() {
    Serial1.end();
    pinMode(PIN_SERIAL1_TX, OUTPUT);
    digitalWrite(PIN_SERIAL1_TX, LOW);
    delay(5);
    digitalWrite(PIN_SERIAL1_TX, HIGH);
    Serial1.begin(57600);
    Serial1.write(0x55);
}


Yes I tried use this

Code:
#include <18F4550.h>
#fuses XT,NOWDT,PUT,BROWNOUT,NOLVP, CPUDIV1
#use delay(clock=4000000)

#define BAUDRATE 9600
#define TX_PIN  PIN_C6
#define RX_PIN  PIN_C7

#use rs232(baud=BAUDRATE, xmit=TX_PIN, rcv=RX_PIN, ERRORS)

void send_break(int8 time_ms)
{
// Disable the UART and send a Break
// for the specified time.
setup_uart(FALSE); 
output_low(TX_PIN);
delay_ms(time_ms);

// Re-enable the UART.
setup_uart(TRUE);
set_uart_speed(BAUDRATE);
}

//======================================
void main(void)
{
int8 c;

printf("Start:\n\r");
   
send_break(20);

while(1)
  {
   c = getc();  // Get a char from the PC
   putc(c);     // Send it back to the PC
  }


}


But no work, I have this
#BIT TX_S = 0xF94.6 // Pin direction mapped to TRISC.6
#BIT RX_S = 0xF94.7 // Pin direction mapped to TRISC.7
Code:
#define BAUDRATE 57600
#define TXD_Lora     PIN_C6    // TXD_Lora
#define RXD_Lora     PIN_C7    // RX_Lora
#use rs232(baud=BAUDRATE,xmit=TXD_Lora,rcv=RXD_Lora,bits=8,parity=N,ERRORS,stream=lora)  // Modulo RN2903
//!#use rs232(baud=57600,xmit=PIN_c6,rcv=PIN_c7,bits=8,parity=N,ERRORS,stream=lora)  // Modulo RN2903
#use rs232(baud=9600,xmit=PIN_b6,rcv=PIN_b7,bits=8,parity=N,ERRORS,stream=debug)  // Puerto DEBUG

    setup_uart(FALSE,lora);             //Serial1.end();
    TX_S=0;                               //pinMode(PIN_SERIAL1_TX, OUTPUT);
    output_low(TXD_Lora);             //digitalWrite(PIN_SERIAL1_TX, LOW);
    delay_ms(100);
    output_high(TXD_Lora);             //digitalWrite(PIN_SERIAL1_TX, HIGH);
    set_uart_speed(BAUDRATE,lora);          //Serial1.begin(57600);
    fprintf(lora,0x55);             //Serial1.write(0x55);


So I don know how "disable" de lora port


There is other code


but how write in CCS?
Code:
void RNsleep(void)
{

  UART_Write_Text("sys sleep 400000000");
  delayXs(1);
}

void RNwakeUp(void)
{
while(!TRMT);
TXREG = 0x00;
while(!TRMT);
TXREG = 0x55;

}
Ttelmah



Joined: 11 Mar 2010
Posts: 19480

View user's profile Send private message

PostPosted: Thu Mar 22, 2018 1:23 am     Reply with quote

Code:

#include <18F4550.h>
#fuses XT,NOWDT,PUT,BROWNOUT,NOLVP, CPUDIV1
#use delay(clock=4000000)

#define BAUDRATE 9600
#define TX_PIN  PIN_C6
#define RX_PIN  PIN_C7

#use rs232(baud=BAUDRATE, xmit=TX_PIN, rcv=RX_PIN, ERRORS)

void send_break(int16 time_ms) //note int16
{
   // Disable the UART and send a Break
   // for the specified time.
   setup_uart(FALSE);
   output_low(TX_PIN);
   delay_ms(time_ms);

   // Re-enable the UART. - sending 'non zero', enables and sets the
   //baud rate
   setup_uart(BAUDRATE);
   putc(0x55); //The character after the break _[u]must[/u]_ be 0x55
}

//======================================
void main(void)
{
   int8 c;

   delay_ms(500); //give time for other things to wake
   printf("Start:\n\r");
   
   send_break(20);
 
   while(TRUE)
   {
      c = getc();  // Get a char from the PC
      putc(c);     // Send it back to the PC
   }
}


What you have would work, except you are missing the 0x55 character that must follow the break. Also you don't need to set the baud rate separately. The setup_uart command can do this in one operation.

Note also the delay. Any module like this (running firmware), takes time to boot. Most need perhaps 100mSec, before they can accept commands after power-on. I can't see anything in the data sheet saying how long it does need, but 'history' says a delay before trying to change the baud rate is probably sensible....
kmp84



Joined: 02 Feb 2010
Posts: 345

View user's profile Send private message

PostPosted: Thu Mar 22, 2018 2:56 am     Reply with quote

Hello,

I'm also using RN2483 Lora modem in peer to peer mode with hardware reset pin without problem.

Best Regards!
asmallri



Joined: 12 Aug 2004
Posts: 1634
Location: Perth, Australia

View user's profile Send private message Send e-mail Visit poster's website

PostPosted: Thu Mar 22, 2018 12:05 pm     Reply with quote

Ttelmah wrote:

Note also the delay. Any module like this (running firmware), takes time to boot. Most need perhaps 100mSec, before they can accept commands after power-on. I can't see anything in the data sheet saying how long it does need, but 'history' says a delay before trying to change the baud rate is probably sensible....


FYI, I tested this with current generation RN2903A modules. It consistently takes 4.6ms to be ready from a software reset or hardware reset. I chose this method over the wake / break sequence because I thought it was cleaner.
_________________
Regards, Andrew

http://www.brushelectronics.com/software
Home of Ethernet, SD card and Encrypted Serial Bootloaders for PICs!!
Ttelmah



Joined: 11 Mar 2010
Posts: 19480

View user's profile Send private message

PostPosted: Thu Mar 22, 2018 12:50 pm     Reply with quote

Useful data. I'd say to use 10mSec to be safe then. Smile
cvargcal



Joined: 17 Feb 2015
Posts: 134

View user's profile Send private message

PostPosted: Thu Mar 22, 2018 2:42 pm     Reply with quote

Thanks to everyone.
I did this:

Code:
#include <18LF26K22.h>
#include <string.h>                             
#include <stdlib.h>
#include <stdio.h>
#use delay(clock=4000000)

#define BAUDRATE 9600
#define TX_PIN  PIN_C6
#define RX_PIN  PIN_C7
#use rs232(baud=BAUDRATE, xmit=TX_PIN, rcv=RX_PIN, ERRORS)
void blink_led(PIN,int1 time_up,int time_down );
void send_break(int16 time_ms){
   // Disable the UART and send a Break  for the specified time.
   setup_uart(FALSE);
   output_low(TX_PIN);
   delay_ms(time_ms);

   // Re-enable the UART. - sending 'non zero', enables and sets the baud rate
   setup_uart(BAUDRATE);
   putc(0x55); //The character after the break _[u]must[/u]_ be 0x55
}

//======================================
void main(void) {
   char c;
   delay_ms(500);
    while(TRUE){
              c=0x00;
              printf("sys sleep 20000\r\n");
              delay_ms(4000); 
              send_break(200);
              printf("sys get ver\r\n");
              delay_ms(200); 
              c = getc(); 
             if (c=="R")   blink_led(pin_c5,20,50);
           
   }
}

//******* Blink LED *********************         
void blink_led(PIN,int1 time_up,int time_down ){
      output_high(PIN);      delay_ms(time_up);
      output_low(PIN);       delay_ms(time_down);
}


but not work... the module not wake up
I not wanted use the PIN RESET... but to end I have do it.
What is the diference if I reset the module to Wake up?...
maybe its better RESET
Ttelmah



Joined: 11 Mar 2010
Posts: 19480

View user's profile Send private message

PostPosted: Thu Mar 22, 2018 3:52 pm     Reply with quote

Does your PSU meet the supply rise time requirements for the unit?. If not, the chip may not be resetting properly on power on. Remember the chip has to have successfully booted, before you can use the 'break' command sequence.
cvargcal



Joined: 17 Feb 2015
Posts: 134

View user's profile Send private message

PostPosted: Tue Aug 07, 2018 11:18 pm     Reply with quote

Ttelmah wrote:
....


I am again here.... I saw this example from microchip, so how I do on CCS?
please

Code:
void moduleResync(void)
{
    // First send wake up / restart autobaud
    TXSTAbits.TXEN = 0;
    EUSART_TX_LAT = 0;
    _delayms(10);
    TXSTAbits.TXEN = 1;
  _delayms(5);
    // Now send autobaud detect character
    TXREG = 0x55;
    while (TXSTAbits.TRMT == 0)
    {};
    // Now send a command to be ignored
    sendCommand("z");
}
Ttelmah



Joined: 11 Mar 2010
Posts: 19480

View user's profile Send private message

PostPosted: Wed Aug 08, 2018 1:07 am     Reply with quote

Er something like:
Code:

    setup_uart(FALSE); //turn off the UART
    output_low(TX_PIN); //select to suit your UART
    delay_ms(10);
    setup_UART(TRUE); //turn UART back on
    delay_ms(5);
    putc(0x55);


Then you would need whatever the 'sendcommand' code has in it.

The autobaud here is for the remote device not the PIC, so it doesn't have to do anything except send a break (which is what turning off the UART, and dropping the TX pin does), and then send the sync character (0x55) to the remote device.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group