 |
 |
| View previous topic :: View next topic |
| Author |
Message |
jameszum
Joined: 31 Jan 2012
Posts: 14
|
| MPLAB ICD 2 in debug mode |
 Posted: Tue Jan 31, 2012 4:28 pm |
 |
|
I am trying to use a MPLAB ICD 2 to debug code for a "24F16KA102" on a "16 bit XLP development board" I connect the MPLAB ICD 2 and launch the PCW program select debug it starts down loading then I get the Error Code 85DE0016.
Clicking diagnostics does nothing and the debugger reports that the "MPLAB ICD 2" is not ready.. There is only a green POWER light on the MPLAB ICD 2
Any help would be appreciated I am using PCWHD v4.129
| Code: | #include <24F16KA102.h>
#Device ICD=2
#device ADC=10
//#fuses debug
#FUSEs NOBSS //No boot segment
#FUSEs NOWRTB // NO Boot Block write protect
#FUSES NOCKSFSM // Clock Switching is disabled, fail Safe clock monitor is disabled
#FUSES NOBROWNOUT // No brownout reset
#FUSES NOWDT // No watch dog timer
#FUSES NOPROTECT // code is not protected from reading
#FUSES NOBROWNOUT // No brownout reset
#FUSES MCLR // Master Clear pin enabled
#FUSES NOPUT // No Power Up Timer
#FUSES NODSBOR // BOR disabled in Deep Sleep
#FUSES NOWRT // Program memory not write protected
#FUSES NOPROTECT // Code not protected from reading
#FUSES NOCKSFSM // Clock Switching is disabled, fail Safe clock monitor is disabled
#FUSES NODSWDT // Deep Sleep Watchdog Timer disabled
#FUSES NOIESO // Internal External Switch Over mode disabled
#FUSES FRC // Internal Fast RC Oscillator
#use delay(clock=8000000)
#include <new_test_004.h>
//#pragma use rs232(force_SW,invert, baud=115200, xmit=PIN_B0, rcv=PIN_B1, bits = 8, parity = N)
#use rs232(force_SW,invert, baud=115200, xmit=PIN_B0, rcv=PIN_B1, bits = 8, parity = N)
#define out15 PIN_B15 // the blinky bit
void main()
{
unsigned int16 value;
setup_adc_ports(sAN12);
setup_adc(ADC_CLOCK_internal); // Built-in A/D setup function
// TODO: USER CODE!!
while(1)
{
value = 0;
set_adc_channel(12); // Built-in A/D setup function
delay_ms(100);
value = read_adc(); // Built-in A/D read function
printf( "this is a test1 %u \n\r",value);
delay_ms(100); // Built-in delay function
output_low(out15); // this works
delay_ms(10);
output_high(out15);
delay_ms(10);
}
}
|
|
|
 |
zagoaristides
Joined: 08 Jul 2007
Posts: 15
Location: Cordoba - Argentina
|
| Re: MPLAB ICD 2 in debug mode |
| Posted: Sun Nov 17, 2013 8:51 am |
|
|
| jameszum wrote: | I am trying to use a MPLAB ICD 2 to debug code for a "24F16KA102" on a "16 bit XLP development board" I connect the MPLAB ICD 2 and launch the PCW program select debug it starts down loading then I get the Error Code 85DE0016.
Clicking diagnostics does nothing and the debugger reports that the "MPLAB ICD 2" is not ready.. There is only a green POWER light on the MPLAB ICD 2
Any help would be appreciated I am using PCWHD v4.129
| Code: | #include <24F16KA102.h>
#Device ICD=2
#device ADC=10
//#fuses debug
#FUSEs NOBSS //No boot segment
#FUSEs NOWRTB // NO Boot Block write protect
#FUSES NOCKSFSM // Clock Switching is disabled, fail Safe clock monitor is disabled
#FUSES NOBROWNOUT // No brownout reset
#FUSES NOWDT // No watch dog timer
#FUSES NOPROTECT // code is not protected from reading
#FUSES NOBROWNOUT // No brownout reset
#FUSES MCLR // Master Clear pin enabled
#FUSES NOPUT // No Power Up Timer
#FUSES NODSBOR // BOR disabled in Deep Sleep
#FUSES NOWRT // Program memory not write protected
#FUSES NOPROTECT // Code not protected from reading
#FUSES NOCKSFSM // Clock Switching is disabled, fail Safe clock monitor is disabled
#FUSES NODSWDT // Deep Sleep Watchdog Timer disabled
#FUSES NOIESO // Internal External Switch Over mode disabled
#FUSES FRC // Internal Fast RC Oscillator
#use delay(clock=8000000)
#include <new_test_004.h>
//#pragma use rs232(force_SW,invert, baud=115200, xmit=PIN_B0, rcv=PIN_B1, bits = 8, parity = N)
#use rs232(force_SW,invert, baud=115200, xmit=PIN_B0, rcv=PIN_B1, bits = 8, parity = N)
#define out15 PIN_B15 // the blinky bit
void main()
{
unsigned int16 value;
setup_adc_ports(sAN12);
setup_adc(ADC_CLOCK_internal); // Built-in A/D setup function
// TODO: USER CODE!!
while(1)
{
value = 0;
set_adc_channel(12); // Built-in A/D setup function
delay_ms(100);
value = read_adc(); // Built-in A/D read function
printf( "this is a test1 %u \n\r",value);
delay_ms(100); // Built-in delay function
output_low(out15); // this works
delay_ms(10);
output_high(out15);
delay_ms(10);
}
}
|
|
SAME ERROR!!! Any help? |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19255
|
|
| Posted: Sun Nov 17, 2013 11:35 am |
|
|
Your board uses the PGC/D3 pins not PGC/D2.
Best Wishes |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
