CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

MAX7219 example and use spi software 5 code lines so easy

 
Post new topic   Reply to topic    CCS Forum Index -> Code Library
View previous topic :: View next topic  
Author Message
trakomaster



Joined: 13 Nov 2011
Posts: 1
Location: Lima, Peru

View user's profile Send private message MSN Messenger

MAX7219 example and use spi software 5 code lines so easy
PostPosted: Sun Nov 13, 2011 12:57 am     Reply with quote

This is an easy program for my power supply, it's really simple, just look at #use spi and void maxsend(){} and that's all. I don't know why people write lots of lines, but this code works with 5 lines including curly braces.

12F683 has no spi hardware so this is useful. Very Happy

I hope you guys like it. Send a message if you want the complete project with proteus.

I'm not good at writing in English. Please don't be mean.

Leave your comments Very Happy Very Happy

Code:
#include <12f683.h>
#fuses intrc_io,noput,nowdt,noprotect,nomclr,nobrownout,noieso,nofcmen
#device adc=10
#use delay(clock=4M)
#use fast_io(a)
#use spi(do=pin_a0,clk=pin_a2,bits=16,load_active=1,load=pin_a1,idle=1)
//We have to write this directive, you can add stream and change the pin do, clk, load
//I've used bits 16 'cause max7219 needs 16 bits =)
//The idle is 1, if you put 0, nothing will appear on your displays <- this is really important


int address, data, adqnum, digit[4];      //address, data max's variables
                                 //adqnum for 100 samples
                                 //digit[4] this array keeps 4 digits used in this project
int16 packetmax, result;               //packetmax goes to the max7219
                                 //result keeps the value used to obtain digits
int32 adcvalue=0;                     //this variable keep the adc value read 100 times
float calculus;                        //variable used for (adcvalue * (5/1023))

void maxsend(){                     //routine for max7219 just
   packetmax=make16(address,data);      //make a 16 bit variable address byte high, data byte low
   spi_xfer(packetmax);            //transfer using spi software
}                              //just 5 lines including #use spi. It's really simple right?

void maxsetup(){                     //configure properly
   address=0x09, data=0xff, maxsend();      //it's up to you
   address=0x0a, data=0x01, maxsend();      //just read a minute the datasheet
   address=0x0b, data=0x03, maxsend();      //it's easy and fast.
   address=0x0f, data=0x00, maxsend();
   address=0x0c, data=0x01, maxsend();
}

void algebra_digits(){
   calculus=adcvalue*0.4887585533;            //500 is the max value, 500=5.00V, but it's float
   result=calculus;                     //transfer the correct value to int result
                                    //if you want to measure a higher voltage just change the float value
                                    //and don't forget using resistors as needed.
                                    
                                    //the following 4 lines are used to obtain digits
   digit[0]=result-((result/10)*10);         //units place
   digit[1]=(result/10)-((result/100)*10);      //tens place   
   digit[2]=(result/100)-((result/1000)*100);   //hundreds place
   digit[3]=result/1000;                  //thousands place
}

void main(){
   setup_comparator(nc_nc_nc_nc);         //no comparator module
   setup_adc(adc_clock_div_16);         //Tad = 4.0us
   setup_adc_ports(an3_analog);         //gpio4 as analog input, u can choose your favorite pin
   set_adc_channel(3);                  //select channel 3 =gpio4
   set_tris_a(0b00011000);               //set port
   delay_ms(1000);                     //wait just for relaxing =), this line is not that important
   maxsetup();                        //

   while(1){
      for(adqnum=1;adqnum<=100;adqnum++){   //collect 100 samples, I usually do this, u can use your favorite method
         adcvalue=adcvalue+read_adc();   //for acquisition.
         delay_us(20);
      }   
      adcvalue=adcvalue/100;
      algebra_digits();                              //call algebra routine to get each digit
      address=0x01, data=digit[0], maxsend();
      address=0x02, data=digit[1], maxsend();
      address=0x03, data=(digit[2] | 0b10000000), maxsend();   //use OR for adding decimal point
      address=0x04, data=digit[3], maxsend();
      adcvalue=0;                                    //clean adcvalue
   }
}
Very Happy
_________________
Physics works!!!
rosiley



Joined: 29 May 2014
Posts: 18
Location: Brasil

View user's profile Send private message

PostPosted: Wed Nov 04, 2015 7:28 am     Reply with quote

Hi, i used your code in my project and need use two max7219 and show two diferent value, i need see adc channel 0 and 1.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> Code Library All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group