CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

Working LCD.c driver for Samsung based chip

 
Post new topic   Reply to topic    CCS Forum Index -> Code Library
View previous topic :: View next topic  
Author Message
sonicdeejay



Joined: 20 Dec 2005
Posts: 112

View user's profile Send private message

Working LCD.c driver for Samsung based chip
PostPosted: Thu Feb 09, 2006 11:13 am     Reply with quote

I am using PIC18F2525 with a 2x16 matric LCD based on S6A0069 and works well so far...(thx to PCM programmer for his helps)



This is my lcdmod.c
Code:

struct lcd_pin_map {                 // This structure is overlayed
           BOOLEAN enable;           // on to an I/O port to gain
           BOOLEAN rs;               // access to the LCD pins.
           BOOLEAN rw;               // The bits are allocated from
           BOOLEAN unused;           // low order up.  ENABLE will
           int     data : 4;         // be pin B0.
        } lcd;


#if defined(__PCH__)
#if defined use_portb_lcd
   #byte lcd = 0xF81                   // This puts the entire structure
#else
   #byte lcd = 0xF83                   // This puts the entire structure
#endif
#else
#if defined use_portb_lcd
   #byte lcd = 6                  // on to port B (at address 6)
#else
   #byte lcd = 8                 // on to port D (at address 8)
#endif
#endif

#if defined use_portb_lcd
   #define set_tris_lcd(x) set_tris_b(x)
#else
   #define set_tris_lcd(x) set_tris_d(x)
#endif


#define lcd_type 2           // 0=5x7, 1=5x10, 2=2 lines
#define lcd_line_two 0x40    // LCD RAM address for the second line


BYTE const LCD_INIT_STRING[4] = {0x20 | (lcd_type << 2), 0xc, 1, 6};
                             // These bytes need to be sent to the LCD
                             // to start it up.


                             // The following are used for setting
                             // the I/O port direction register.

struct lcd_pin_map const LCD_WRITE = {0,0,0,0,0}; // For write mode all pins are out
struct lcd_pin_map const LCD_READ = {0,0,0,0,15}; // For read mode data pins are in



BYTE lcd_read_byte() {
      BYTE low,high;
      set_tris_lcd(LCD_READ);
      lcd.rw = 1;
      delay_cycles(1);
      lcd.enable = 1;
      delay_cycles(1);
      high = lcd.data;
      lcd.enable = 0;
      delay_cycles(1);
      lcd.enable = 1;
      delay_us(1);
      low = lcd.data;
      lcd.enable = 0;
      set_tris_lcd(LCD_WRITE);
      return( (high<<4) | low);
}


//Modified code to fit S6A0069 chip based LCD
void lcd_send_nibble( BYTE n ) {
      lcd.data = n;
      delay_cycles(1);
      lcd.enable = 1;
      delay_us(2);
      lcd.enable = 0;
}


//Orignal LCD format
/*void lcd_send_nibble( BYTE n ) {
      lcd.data = n;
      delay_cycles(1);
      lcd.enable = 1;
      delay_us(2);
      lcd.enable = 0;
}*/


void lcd_send_byte( BYTE address, BYTE n ) {

      lcd.rs = 0;
      while ( bit_test(lcd_read_byte(),7) ) ;
      lcd.rs = address;
      delay_cycles(1);
      lcd.rw = 0;
      delay_cycles(1);
      lcd.enable = 0;
      lcd_send_nibble(n >> 4);
      lcd_send_nibble(n & 0xf);
}

//Modified code to fit S6A0069 chip based LCD
void lcd_init() {
    set_tris_lcd(LCD_WRITE);
    lcd.rs = 0;
    lcd.rw = 0;
    lcd.enable = 0;
    delay_ms(30);
   lcd_send_nibble(0x02);
   delay_us(1);
    lcd_send_nibble(0x02);
    delay_us(1);
    lcd_send_nibble(0x0C);
    delay_us(45);
    lcd_send_nibble(0x00);
    delay_us(1);
    lcd_send_nibble(0x0F);
    delay_us(45);
    lcd_send_nibble(0x00);
    delay_us(1);
    lcd_send_nibble(0x01);
    delay_ms(2);
    lcd_send_nibble(0x00);
    delay_us(1);
    lcd_send_nibble(0x06);
    delay_ms(2);

}

//Orignal LCD format
/*
void lcd_init() {
    BYTE i;
    set_tris_lcd(LCD_WRITE);
    lcd.rs = 0;
    lcd.rw = 0;
    lcd.enable = 0;
    delay_ms(15);
    for(i=1;i<=3;++i) {
       lcd_send_nibble(3);
       delay_ms(5);
    }
    lcd_send_nibble(2);
    for(i=0;i<=3;++i)
       lcd_send_byte(0,LCD_INIT_STRING[i]);
}*/

void lcd_gotoxy( BYTE x, BYTE y) {
   BYTE address;

   if(y!=1)
     address=lcd_line_two;
   else
     address=0;
   address+=x-1;
   lcd_send_byte(0,0x80|address);
}

void lcd_putc( char c) {
   switch (c) {
     case '\f'   : lcd_send_byte(0,1);
                   delay_ms(2);
                                           break;
     case '\n'   : lcd_gotoxy(1,2);        break;
     case '\b'   : lcd_send_byte(0,0x10);  break;
     default     : lcd_send_byte(1,c);     break;
   }
}


Last edited by sonicdeejay on Fri Feb 24, 2006 5:21 pm; edited 1 time in total
sonicdeejay



Joined: 20 Dec 2005
Posts: 112

View user's profile Send private message

PostPosted: Mon Feb 20, 2006 7:19 pm     Reply with quote

In my main program..



Code:
#include <18F2525.h> // Call for PIC18F2525 Driver
#device ICD=TRUE
#device ADC=10 // Use 10bits ADC
#fuses HS,NOWDT,NOPROTECT,NOLVP
#use delay(clock=16000000) // 16Mhz Crystal is Used
#use rs232(baud=9600, parity=N, xmit=PIN_C6, rcv=PIN_C7, bits=8)  // RS232 Configuration for COM Port Communication



#define use_portb_lcd TRUE // Using Port B for LCD Display
#include <lcdmod.c>  // This is Where I call for lcdmod.c



#byte PORTB = 0xf81
#byte PORTC = 0xf82

#include <stdlib.h>
#include <math.h>
sonicdeejay



Joined: 20 Dec 2005
Posts: 112

View user's profile Send private message

PostPosted: Sun Feb 26, 2006 6:29 am     Reply with quote

My physical connection is ...

Code:
  LCD  -   PIC18F2525

 VSS   -   GND
 VDD   -   5V
 V0    -    O/P from variable ressitor (20KOhm)

 R/S   -  PORT_B1
 R/W   -  PORT_B2
 E     -  PORT_B0

 DB0   -   NC (not connected)
 DB1   -   NC (not connected)
 DB2   -   NC (not connected)
 DB3   -   NC (not connected)
 DB4   -  PORT_B4
 DB5   -  PORT_B5
 DB6   -  PORT_B6
 DB7   -  PORT_B7



Wink
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> Code Library All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group